Dsc Pc5010 Installer Code For Windows 7
Dsc 5010 Installer Code
Dsc Pc5010 Installer Code Reset

May 18, 2016 I have the installer code for my DSC security system (PK5500 or 5501) and want to use it to change the master code. Lost that one & can't figure it out but guessed the installer code. Technician's Assistant: Sometimes things that you think will be really complicated end up being easy to fix. Subject: PC5010 version 1 user guide Keywords: Power 832, 832, PC5010, 5010, DSC Created Date: 6:50:29 PM Power 832 user - Action Security Systems, Inc. View and Download DSC Power 832 installation manual online. Security system. Power 832 security system pdf manual download. Also for: Pc5o15. DSC POWER 832 INSTALLATION.

Is the yellow ‘trouble’ LED lit on your alarm keypad? DSC uses LED codes to indicate trouble details for all keypads that don’t have an LCD readout display. The following applies to all PowerSeries panels, which include PC1616, PC1832, PC5010, PC5015 and others.

To view system troubles, press:

Service Required (press [1] for more information)
1. Low Battery (main battery in panel)
2. Bell Circuit
3. System Trouble
4. System Tamper
5. Module Supervision
6. RF Jam Detected
7. PC5204 Low Battery
8. PC5204 AC Failure
AC Failure
- AC power is not present at the panel (the system is operating on stand-by battery power.
Telephone Line Trouble
- The panel does not detect an active telephone line.
Failure to Communicate
- The system attempted to communicate with the monitoring station but failed.
Zone Fault (press [5] for more information)
- The system is experiencing difficulties with one or more sensors or zones.
- Press [5] for the keypad to display which zone is experiencing the fault.
Zone Tamper (press [6] for more information)
- The system has detected a tamper on one or more sensors on the system.
- Press [6] for the keypad to display which zone is tampered.
Device Low Battery (press [7] for more information)
- A wireless device has a low battery.
- Press [7] for the keypad to display which zone has a low battery.
Loss of System Time
- If complete power was lost (AC and battery), the time and date will need to be re-programmed.
- To program the time, press

admin • 14/02/2015

Next Post ↠

Managing Users on a DSC Alarm System

FAQs

Arming from an LED Keypad:

If the Ready light is ON, the system is ready for arming. If the Ready light is OFF, check to see that all doors and windows are closed and that motion is stopped in areas covered by motion detectors. The system Cannot be armed unless the Ready light is ON indicating that all zones are closed and the system is in the Ready state.

Enter your [User code]. As each digit is entered, the keypad sounder will beep. If the access code was entered incorrectly, the keypad buzzer will sound steadily for two seconds. If this occurs, press the [#] key and re-enter your [User code]. If the correct access code is entered, the keypad sounder will beep quickly and the Armed light will come ON. Exit the premises through the door indicated by your installer as the Exit/Entry door.

The panel will provide an exit delay period, indicated by keypad beeps, for you to exit the premises without causing an alarm. At the end of the exit delay period, the Ready light will turn OFF and the system will be armed. The exit delay time can be changed by your installer.

Arming from an LCD Keypad:

Secure System
Before Arming<>

When this message appears, one or more zones are not secured. To secure the system, close all doors and windows and cease all motion in areas covered by motion detectors.

Enter Code to
Arm System <>

When this message appears, use the arrow (< >) keys to verify that the system is clear of troubles and that no zones are bypassed unintentionally.

Enter Code to
Arm System

If this display is showing, the system is in the Ready state and may be fully armed. To arm the system, enter your [User code].

Exit Delay in
Progress

Once the correct user code has been entered, the display will be as shown. The panel will provide an exit delay period, also indicated by keypad beeps, for you to exit the premises without causing an alarm. You can restart the exit delay once by pressing the [Away] button before the exit delay expires. Exit through the door indicated by your installer as the Exit/Entry door.

Exit Code to
Disarm System

This message will be displayed once the exit delay expires and the system is fully armed.

*WARNING*
Bypass Active

If this message appears, be aware of which zones are bypassed and why.

NOTE: If you arm the system with a zone bypassed or with a trouble present, your security protection is reduced.

Alternate Arming Methods Away Arming:

Arming the system in the Away mode will have all interior zones and perimeter zones active. If motion is detected in the interior zones, or if one of the perimeter zones is violated, the alarm sequence will begin. To arm in the Away mode, enter your [User code] and exit the premises through a designated Exit/Entry door. The system will recognize that occupants have left the premises. Once the exit delay expires, the system will be fully armed.

Audible Exit Fault:

In an attempt to reduce false alarms, the Audible Exit Fault is designed to notify you of an improper exit when arming the system in the Away mode. In the event that you fail to exit the premises during the allotted exit delay period, or if you do not securely close the Exit/Entry door, the system will notify you that it was improperly armed in two ways: the keypad will emit one continuous beep and the bell or siren will sound. If this occurs, you must re-enter the premises, enter your [User code] to disarm the system, and then follow the arming procedure again, making sure to exit the premises in the proper fashion. Your installer will tell you if the Audible Exit Fault has been enabled on your system.

Stay Arming:

This feature, if enabled by your installer, will allow you to arm the perimeter zones while leaving the interior zones inactive so that you can remain on the premises while the system is armed. When you enter your [User code] to arm the system and do not exit the premises through a designated Exit/ Entry door, the system will arm in the Stay mode, automatically bypassing the interior zones.

The interior zones can be reactivated at any time by entering [*] [1] at any keypad. If you reactivate the interior zones, be sure to only inhabit areas not covered by motion detectors. To access areas protected by motion sensors, you must enter your [User code] and disarm the system.

Arming Without Entry Delay:

If you wish to arm your system without the entry delay, enter [*] [9] then your [User code]. The Armed light will flash as a reminder that the system is armed and has no entry delay. An entry through any zone programmed as a delay zone will create an instant alarm.

Quick Arm:

When the Quick Arm feature is enabled, the system may be armed by simply pressing [*] [0]instead of your User code. Please note that pressing [*] [0] will only allow you to arm the system; to disarm; you must enter a valid [User code]. Your installer will inform you if the Quick Arm feature has been enabled on your system.

Quick Exit:

When the Quick Exit feature is enabled, pressing [*] [0] while the system is armed will provide a two minute window for you to exit the premises. During this time, you may only open and close the designated Entry/Exit door once. Once the door is closed, the panel will end the two minute quick exit delay. If the door is opened again, or if the door is n

Dsc Pc5010 Installer Code